Geeetech TG17 3D Pen With ABS PLA PCL LCD Display Show Speed Adjustable Replaceable Nozzle Children Educational Toy Gift

lSupports ABS,PLA, PLC: TG-17 has 3 modes for supporting ABC,PLA,PCL 3 different temperature-supported filament, allow you to choose freely

l 5 gears of speed for real-time adjustment: TG-17 has 5 gears of speed for adjustment. Users can adjust the extrusion speed of filament according to his needs during use. What’s more, compared to other products, TG-17 can continue printing process while adjusting speed, bringing users smooth and joyful printing experience.

lAdjustable printing temperature: in ABS, PLA, PLC 3 modes, the printing temperature can all be adjusted. If you find that the filament is difficult to extrude, filament too thin or bubbling, you can solve it by adjusting printing temperature.

l Smart sleep mode: for your safety and protection of the 3D printing pen, when the printing pen does not start printing within one minute after preheating or continuously extrude for 8 minutes, the printing pen will stop heating and stop printing, it automatically go to sleep mode. If you want to use it again, press the extrusion button;

lDetachable pen tip:for the convenience of cleaning and maintenance, the ceramic nozzle of the printing pen adopts a detachable design. When the pen tip needs to be cleaned or damaged, only needs to remove the pen tip to clean or repair;

lExternal power supply: TG-17 adopts an external 5V power supply. Compared with the built-in battery-type 3D printing pen, there is no need to worry about the power life of the printing pen;

Operation Instructions

1, After connecting the pen to the power supply(5V/2A), it enter into

standby condition when the LED screen displays « PLA » or « ABS ».

2,After switch the filament mode between PLA and ABS, press the »L »button to choose « PLA »or »ABS »,press the  » ▼ « button once to heat, when the power indicator turns green ,press the « ▼ »button load the PLA filament.

3, Press « L » button to adjust temperature and speed.

4, Press the  » ▼  » button once to start loading, press the  » ▲  » button once to start unloading automatically.

5, After using the pen, please press the button  » ▲ « to unload the filament, please finish unloading progress at one time.

6.This product will automatically enter into standby mode without using of 3 minutes and the LCD screen displays  » »SLEEP » ». Please press the  » ▼ » button once to activate.

Product Features

Discharge method: hot melt extrusion stacking

Nozzle diameter: 0.6mm

Voltage: 5V/2A (with IC protection head)

Operating Temperature: 180-220℃ degree adjustable

Printing Speed: Low, Medium, High speed

Suitable Filament: PLA/ABS 1.75mm

Screen: LCD HD display

Material:PlasticTip

material: porcelain

Package Contents:

1×3D printing pen

1×Power Adapter

1×Micro USB cable

1×User Manual

1×Pen holder

1×PVC Drawing board

1×Transparentmat

1×finger stall

1×3D Drawing Stencils

1×2colors (random)*10 feets FLA filament

Safety and Warning Instruction

1, This device is suitable for use in children and adults aged 8 or above ,below can be uesdful

2, Pay attention to the temperature of the nozzle, please DO NOT touch the nozzle during use to avoid burning your hand.

3, Please exit out of 3D Pen Filament Refills and cut off the power supply after using

4, Please put the pen in a place where children can not touch after using.

5. Please do not use the nib to touch other hard objects.

6. Please do not use foreign materials to load the hole of load the filament or the nib.

7. Please do not use other manufacturers’ consumables, so as not to cause incompatibility.

8. The eduipment for precision electroinc equipment ,do not spray water ,and this product is not waterproof.

Precautions:

1.Check

that the filament interface if flat or not before each using,

otherwise, the uneven filament will block the delivery tube.

2.When

entering the sleep mode, after pressing the feed button, the

temperature needs to rise again. The longer the sleep time, the longer

it takes to wait.

3.Please put the corresponding ABS/PLA filament according to the selected mode.